xgnokii настроен не на тот порт
Собственно сабж.
У меня Nokia 6610i. Через irdadump определяется. Находится на порту /dev/ttyS1.
Но вот с gnokii проблема:
# xgnokii LOG: debug mask is 0x1 (xgnokii:4269): Gtk-WARNING **: horizontal scrolling not implemented (xgnokii:4269): Gtk-WARNING **: horizontal scrolling not implemented phone instance config: model: 6510 port_device: /dev/ttyS0 connection_type: 0 init_length: 0 serial_baudrate: 19200 serial_write_usleep: -1 hardware_handshake: 0 require_dcd: 0 smsc_timeout: 100 connect_script: disconnect_script: rfcomm_cn: 1 sm_retry: off Connecting Serial device: opening device /dev/ttyS0 Gnokii serial_open: tcgetattr: Ошибка ввода/вывода Couldn't open FBUS device: Ошибка ввода/вывода Error in link initialisation: 1 Serial device: opening device /dev/ttyS0 Gnokii serial_open: tcgetattr: Ошибка ввода/вывода Couldn't open FBUS device: Ошибка ввода/вывода Error in link initialisation: 1 Serial device: opening device /dev/ttyS0 Gnokii serial_open: tcgetattr: Ошибка ввода/вывода Couldn't open FBUS device: Ошибка ввода/вывода Error in link initialisation: 1 GSM/FBUS init failed! (Unknown model?). Quitting. Serial device: closing device
Где все это дело редактируется? Гугление не помогло...
Мы ушли на www.asplinuxclub.org - как не справивишиеся с обязанностями модераторов
- Добавить комментарий
- 6829 просмотра
Вход
Подписка на RSS
Фото из альбома
Re: xgnokii настроен не на тот порт #1
Админ админу - друг, товарищ и ман...
(c) Almaty
Re: xgnokii настроен не на тот порт #2
Re: xgnokii настроен не на тот порт #3
1/ После загрузки `service irda start` посмотрите что выдал dmesg....
2/ Посмотрите какие новые устройства появились в /dev/
Какая у Вас модель irda?
Что пишет производитель? Есть ли хоть какая-то документация и упоминание о чипе, на котором irda-устройство реализовано?
Админ админу - друг, товарищ и ман...
(c) Almaty
Re: xgnokii настроен не на тот порт #4
Какая у Вас модель irda?
Что пишет производитель? Есть ли хоть какая-то документация и упоминание о чипе, на котором irda-устройство реализовано?
в /dev появилось устройство ircomm
модель tekram irmate 210
про чип пока ничего найти не могу, команда findchip -v ничего не показывает.
Re: xgnokii настроен не на тот порт #5
Обратите внимание на /usr/share/doc/irda-utils-0.9.16/README.irattach
/usr/share/doc/irda-utils-0.9.16/modprobe.conf.irda
IMHO, Там есть о Вашей irda. Скорее всего, необходимо добавить параметр в
[sergeil@homedesk sysconfig]$ cat /etc/sysconfig/irda
DONGLE=tekram
...
Но гарантировать не могу, поскольку попробовать не на чем...
Админ админу - друг, товарищ и ман...
(c) Almaty
Re: xgnokii настроен не на тот порт #6
Мы ушли на www.asplinuxclub.org - как не справивишиеся с обязанностями модераторов
Re: xgnokii настроен не на тот порт #7
за вчера и сегодня вот к чему пришел
xgnokii
LOG: debug mask is 0x1
(xgnokii:5592): Gtk-WARNING **: horizontal scrolling not implemented
(xgnokii:5592): Gtk-WARNING **: horizontal scrolling not implemented
phone instance config:
model: 6230
port_device: /dev/ttyS0
connection_type: 4
init_length: 0
serial_baudrate: 19200
serial_write_usleep: -1
hardware_handshake: 0
require_dcd: 0
smsc_timeout: 100
connect_script:
disconnect_script:
rfcomm_cn: 1
sm_retry: off
Connecting
Serial device: opening device /dev/ttyS0
Nokia 6230 939b
connect: Нет пути до хоста
Couldn't open PHONET device: Нет пути до хоста
Error in link initialisation: 1
GSM/FBUS init failed!
Serial device: closing device
телефон мой она определяет, но что означает нет пути до хоста ???
Re: xgnokii настроен не на тот порт #8
(xgnokii:5592): Gtk-WARNING **: horizontal scrolling not implemented
(xgnokii:5592): Gtk-WARNING **: horizontal scrolling not implemented
У меня только циферки другие:
Это сообщение при работающем интернет через инфракрасник. А вот без подключения к интернет:
Поиск решения проблемы пока ничего не дал...
Мы ушли на www.asplinuxclub.org - как не справивишиеся с обязанностями модераторов
Re: xgnokii настроен не на тот порт #9
Re: xgnokii настроен не на тот порт #10
Мы ушли на www.asplinuxclub.org - как не справивишиеся с обязанностями модераторов
Re: xgnokii настроен не на тот порт #11
Так что, шнурок работает...
Админ админу - друг, товарищ и ман...
(c) Almaty
Re: xgnokii настроен не на тот порт #12
Мы ушли на www.asplinuxclub.org - как не справивишиеся с обязанностями модераторов
Re: xgnokii настроен не на тот порт #13
Обмен произошел. Модель определена...
Вы н
Цитата:
Sorry, this function is known to break your phone (Nokia phones series 40 v1).
Refusing to do it. You may try to use AT driver.
Прошу прощения. Неправильно выразился...
Имел в виду что загвоздка в драйвере...
Нет, тестером быть не могу...телефон один и очень нужен...
Не стоит так сразу. Драйвер AT не повредит ваш телефон, не волнуйтесь. Это очень ограниченный драйвер (к сожалению я вынужден пользоваться им) подробно о его возможностях можно прочить на сайте. Но я уже скажу кратко: он работает почти со всеми телефонами (не обязательно nokia), но зато возможности примитивны, фактически это расширенный набор AT команд как для обычного модема. А именно что может быть доступно: просмотр/редактирование телефонной книги, может набирать номер, смотреть/посылать sms, редактировать календарь. У мнея все работает корректно только под utf8. С таким набором в общем это только для xgnokii. Чего не получиться с таким драйвером: mms, скачивание/закачивание файлов. Не бойтесь он ничего не повредит. Если все-таки есть сомнения, но можно сделать резервную копию телефона прогой nokia pcsuite. И помните, через irda не сможете получить доступ в ОС телефона, т.ч. даже если вы не осторожно что-то сделаете, то пострадают только данные. Я сам долго мучался с Nokia6020, несколько более продвинутая прога это gammu (это командная строка), пробуйте, пишите!
Re: xgnokii настроен не на тот порт #14
Мы ушли на www.asplinuxclub.org - как не справивишиеся с обязанностями модераторов
Re: xgnokii настроен не на тот порт #15
Re: xgnokii настроен не на тот порт #16
взял у знакомого шнур для телефона, с ним так же не получилось как и через ИК. Ставил gammu , кстате графическая оболочка под нее называется wammu, через нее тоже тишина.
Скачал последнюю версию gnokii 0.6.13 , поставил. Попробовал сперва со шнуром без запиночки соединился , обрадовался, начал через ИК, и тут снова облом
xgnokii
LOG: debug mask is 0x1
(xgnokii:10112): Gtk-WARNING **: horizontal scrolling not implemented
(xgnokii:10112): Gtk-WARNING **: horizontal scrolling not implemented
phone instance config:
model: 6510
port_device: /dev/ircomm0
connection_type: 4
init_length: 0
serial_baudrate: 19200
serial_write_usleep: -1
hardware_handshake: 0
require_dcd: 0
smsc_timeout: 100
connect_script:
disconnect_script:
rfcomm_cn: 1
sm_retry: off
Connecting
Serial device: opening device /dev/ircomm0
Expecting:
Default: Nokia 6230 444
connect: Нет пути до хоста
Couldn't open PHONET device: Нет пути до хоста
Error in link initialisation: 1
Telephone interface init failed: Command failed.
Quitting.
Failed to open the phone. Quitting.
Serial device: closing device
Re: xgnokii настроен не на тот порт #17
[global]
# Set port to the physical port used to connect to your phone.
# Linux version is:
#port = /dev/ttyS1
#
# For MacOSX you will need something like:
# port = /dev/cu.USA28X1P1.1
#
# For Win32 you want to use:
# port = com1:
# or similiar.
#
# FreeBSD (probably NetBSD and OpenBSD too) use:
# port = /dev/cuaa0
#
# With Linux-IrDA you will want to use
port = /dev/ircomm0
# or similiar.
#
# Use this setting also for the Bluetooth connection:
# port = aa:bb:cc:dd:ee:ff
# when using it with AT driver set it to:
# port = /dev/rfcomm0
# or similiar.
#
# For the Linux USB cables you will need one of the following settings (or
# similiar)
# port = /dev/ttyUSB0
# port = /dev/tts/USB0
# port = /dev/ttyACM0
# the last one will work only with AT driver. The correct setting should be
# given in the dmesg output.
# Set model to the model number of your phone. For the
# Symbian phones use:
# model = series60
# For other non-Nokia phones and when you want to use AT
# mode use:
# model = AT
# If you can't figure out what to put here read the FAQ.
# If it still doesn't help, consult gnokii-ml or #gnokii at freenode.
model = 6610i
# There are few main models that should make use of the certain drivers.
# These are: 6110, 7110, 6510, 3110, 2110, 6160.
# Initlength controls the number of characters sent to the
# phone during initialisation. You can either set it to
# the word "default" or a positive integer.
#
# You can try setting this value if you want to connect
# to the phone quicker. If you've never noticed the
# connection to be slow, it is suggested that you
# leave this alone. Read the initialisation code in fbus-xxxx
# to understand what this changes if you're curious.
initlength = 128
# The type of the connection, for IR set this to infrared or irda.
# For the nk6110 driver only infrared is valid for the IrDA connection.
# See Docs/gnokii-ir-howto for more detailes on this.
# If you have 6210/6250/7110 phone and dau9p cable (the one you can
# use with 6100 series and cannot use hardware modem from the phone)
# you may want to use 'dau9p' value to get faster initialization.
# If you use dlr3 or dlr3p cable for nokia phones in FBUS mode (ie.
# you don't use model = AT) you may want to use 'dlr3p' value here.
# Note that it is recommended and currently the best way to use this
# cable with nk6510 driver.
#connection = dlr3p
# With DKU-2 cable use the following setting
# connection = dku2
# With DKU-5 cable use the following setting
# connection = dlr3p
# For Bluetooth and AT driver use the following setting
#connection = serial
# For other Bluetooth settings use
# connection = bluetooth
# For infraded connection with phones other then Nokia 6110/6130/6150 use
connection = irda
# Set this to 'yes' if you want gnokii to set and check the lock file in
# /var/lock directory. It avoids potential conflicts with other serial
# port software (eg. minicom). If you have wrong permissions for the
# directory, a warning will be generated. If you don't want a lockfile, set
# it to 'no'.
use_locking = yes
# Baudrate to use on serial port connections.
# Currently used only by models AT and BIP/CIMD. Defaults to 19200.
serial_baudrate = 19200
# Force waiting after each send character the specified usec time.
# Value -1 forces the fastest 'block' writing,
# value 0 writes each character separately without any explicite waiting,
# other positive values specify the appropriate 1/1000000 sec delaying.
# Siemens M20 requires at least "1"! FIXME: Model-driven autodetection
#serial_write_usleep = 10000
# Force serial port handshaking mode, useful primarily for "AT" model.
# Gnokii "AT" model uses software handshake by default.
# Possible values: hardware (RTS/CTS - 7 wires) or software (XON/XOFF - 3 wires)
#handshake = software
# If defined (not commented out by '#') it will quit Gnokii anytime
# when DCD line will drop.
#require_dcd = 1
# If you are using a bluetooth connection, you can specify the rfcomm
# channel number here. Default value is 1.
#rfcomm_channel = 1
# There may happen various timeouts during the communication with the phone.
# This parameter enables the retransmission policy. Ie. if the phone doesn't
# respond, we send the frame again. This happend mainly with the older
# phones. You may want to enable it when you see mysterious timeouts.
# Be very carefull with this option. It is suspected to cause phone breakage
# with new DCT4 phones (like Nokia 6100). By default it is switched off
# (sm_retry = 0)
#sm_retry = 1
# Run the specified script(s) right after opening and initializing the device
# and before any communucation (right before closing for disconnect_script).
# You may find handy to use it to connect your modem to SMS Center
# when using BIP or CIMD protocols
# Non-absolute path is relative to the specific directory where gnokii is run!
#connect_script = /absolute/path/to/gnokii/Docs/sample/cimd-connect
#disconnect_script =
# When sending SMS you can experience timeouts. This is the feature of the
# overloaded SMSCs. The phones waits for the response from the SMSC confirming
# that it received the short message. When the SMSC is DoSed with many requests
# it will take more time to get the response. Adjust it to your needs. The
# value is given in seconds to wait. Defaults to 10 seconds. Set to 0 to wait
# forever.
smsc_timeout = 10
# Set bindir to point to the location of the various gnokiid binaries.
# In particular ensure that mgnokiidev is in this location, with
# permissions 4750, owned by root, group gnokii. Ensure you
# are in the gnokii group and that the group exists...
[gnokiid]
bindir = /usr/sbin/
# Any entries in the following two sections will be set as environment
script.
# variables when running the scripts.
# Handy for use for $VAR substitutions in your chat(
[connect_script]
TELEPHONE = 12345678
[disconnect_script]
# The following parameters control how libgnokii handle the debugging messages.
# Currently there are three categories: "debug" controls the libgnokii
# normal debug output, "rlpdebug" controls the debug output of the RLP
# subsystem, and "xdebug" is used by the xgnokii or smsd.
[logging]
# where to log the debug output (on: stderr, off: /dev/null)
debug = on
# where to log the rlp debug output (on: stderr, off: /dev/null)
rlpdebug = off
# where to log X debug output (on: stderr, off: /dev/null)
xdebug = off
Может поможет?
Спасибо, договорились.
Мы ушли на www.asplinuxclub.org - как не справивишиеся с обязанностями модераторов
Re: xgnokii настроен не на тот порт #18
Скачай версию 6.13 она специально для твоего телефона
И еще в файле gnokiirc в строчке model должно прописано 6510, а не твой телефон(6610i)
И если поставишь версию 6.13 заново исправь gnokii, там еще есть новая строка для твоего телефона
Re: xgnokii настроен не на тот порт #19
Мы ушли на www.asplinuxclub.org - как не справивишиеся с обязанностями модераторов
Re: xgnokii настроен не на тот порт #20
Re: xgnokii настроен не на тот порт #21
Мы ушли на www.asplinuxclub.org - как не справивишиеся с обязанностями модераторов
Re: xgnokii настроен не на тот порт #22
[global]
# Set port to the physical port used to connect to your phone.
# Linux version is:
# port = /dev/ttyS0
#
# For MacOSX you will need something like:
# port = /dev/cu.USA28X1P1.1
#
# For Win32 you want to use:
# port = com1:
# or similiar.
#
# FreeBSD (probably NetBSD and OpenBSD too) use:
# port = /dev/cuaa0
#
# With Linux-IrDA you will want to use
port = /dev/ircomm0
# or similiar.
#
# Use this setting also for the Bluetooth connection:
# port = aa:bb:cc:dd:ee:ff
# when using it with AT driver set it to:
# port = /dev/rfcomm0
# or similiar.
#
# For the Linux USB cables you will need one of the following settings (or
# similiar)
# port = /dev/ttyUSB0
# port = /dev/tts/USB0
# port = /dev/ttyACM0
# the last one will work only with AT driver. The correct setting should be
# given in the dmesg output.
# Set model to the model number of your phone. For the
# Symbian phones use:
# model = series60
# For other non-Nokia phones and when you want to use AT
# mode use:
# model = AT
# If you can't figure out what to put here read the FAQ.
# If it still doesn't help, consult gnokii-ml or #gnokii at freenode.
model = 6230
# There are few main models that should make use of the certain drivers.
# These are: 6110, 7110, 6510, 3110, 2110, 6160.
# Set IrDA device name.
# If you use irda connection you may want gnokii to autodetect the irda
# device it connects to. This is fine for most of the cases. if you have
# more than one device in range you may want to give manually the device
# name so gnokii correctly recognizes it. Use the name that you can see
# in the discovery log when the phone with infrared is in the range of
# your irda port.
# Note that you need to set this for each phone_ section separately. It
# isn't nested from the global section.
# irda_string = Nokia 6610i
# Initlength controls the number of characters sent to the
# phone during initialisation. You can either set it to
# the word "default" or a positive integer.
#
# You can try setting this value if you want to connect
# to the phone quicker. If you've never noticed the
# connection to be slow, it is suggested that you
# leave this alone. Read the initialisation code in fbus-xxxx
# to understand what this changes if you're curious.
initlength = 128
# The type of the connection, for IR set this to infrared or irda.
# For the nk6110 driver only infrared is valid for the IrDA connection.
# See Docs/gnokii-ir-howto for more detailes on this.
# If you have 6210/6250/7110 phone and dau9p cable (the one you can
# use with 6100 series and cannot use hardware modem from the phone)
# you may want to use 'dau9p' value to get faster initialization.
# If you use dlr3 or dlr3p cable for nokia phones in FBUS mode (ie.
# you don't use model = AT) you may want to use 'dlr3p' value here.
# Note that it is recommended and currently the best way to use this
# cable with nk6510 driver.
# connection = serial
# With DKU-2 cable use the following setting if you want to libusb driver
# (recommended):
# connection = dku2libusb
# or the following setting if you want to use Linux kernel driver
# connection = dku2
# With DKU-5 cable use the following setting
# connection = dku5
# For Bluetooth and AT driver use the following setting
# connection = serial
# For other Bluetooth settings use
# connection = bluetooth
# For infrared connection with phones other than Nokia 6110/6130/6150 use
connection = irda
# Set this to 'yes' if you want gnokii to set and check the lock file in
# /var/lock directory. It avoids potential conflicts with other serial
# port software (eg. minicom). If you have wrong permissions for the
# directory, a warning will be generated. If you don't want a lockfile, set
# it to 'no'.
use_locking = yes
# Baudrate to use on serial port connections.
# Currently used only by models AT and BIP/CIMD. Defaults to 19200.
serial_baudrate =19200
# Force waiting after each send character the specified usec time.
# Value -1 forces the fastest 'block' writing,
# value 0 writes each character separately without any explicite waiting,
# other positive values specify the appropriate 1/1000000 sec delaying.
# Siemens M20 requires at least "1"! FIXME: Model-driven autodetection
#serial_write_usleep = 10000
# Force serial port handshaking mode, useful primarily for "AT" model.
# Gnokii "AT" model uses software handshake by default.
# Possible values: hardware (RTS/CTS - 7 wires) or software (XON/XOFF - 3 wires)
#handshake = software
# If defined (not commented out by '#') it will quit Gnokii anytime
# when DCD line will drop.
#require_dcd = 1
# If you are using a bluetooth connection, you can specify the rfcomm
# channel number here. Default value is 1.
#rfcomm_channel = 1
# There may happen various timeouts during the communication with the phone.
# This parameter enables the retransmission policy. Ie. if the phone doesn't
# respond, we send the frame again. This happend mainly with the older
# phones. You may want to enable it when you see mysterious timeouts.
# Be very carefull with this option. It is suspected to cause phone breakage
# with new DCT4 phones (like Nokia 6100). By default it is switched off
# (sm_retry = 0)
#sm_retry = 1
# Run the specified script(s) right after opening and initializing the device
# and before any communication (right before closing for disconnect_script).
# You may find handy to use it to connect your modem to SMS Center
# when using BIP or CIMD protocols
# Non-absolute path is relative to the specific directory where gnokii is run!
#connect_script = /absolute/path/to/gnokii/Docs/sample/cimd-connect
#disconnect_script =
# When sending SMS you can experience timeouts. This is the feature of the
# overloaded SMSCs. The phones waits for the response from the SMSC confirming
# that it received the short message. When the SMSC is DoSed with many requests
# it will take more time to get the response. Adjust it to your needs. The
# value is given in seconds to wait. Defaults to 10 seconds. Set to 0 to wait
# forever.
smsc_timeout = 10
# Set bindir to point to the location of the various gnokiid binaries.
# In particular ensure that mgnokiidev is in this location, with
# permissions 4750, owned by root, group gnokii. Ensure you
# are in the gnokii group and that the group exists...
[gnokiid]
bindir = /usr/local/sbin/
# Any entries in the following two sections will be set as environment
script.
# variables when running the scripts.
# Handy for use for $VAR substitutions in your chat(
[connect_script]
TELEPHONE = 12345678
[disconnect_script]
# The following parameters control how libgnokii handle the debugging messages.
# Currently there are three categories: "debug" controls the libgnokii
# normal debug output, "rlpdebug" controls the debug output of the RLP
# subsystem, and "xdebug" is used by the xgnokii or smsd.
[logging]
# where to log the debug output (on: stderr, off: /dev/null)
debug = on
# where to log the rlp debug output (on: stderr, off: /dev/null)
rlpdebug = off
# where to log X debug output (on: stderr, off: /dev/null)
xdebug = off