Отсутствует звук, но ... музыка играет!

Аватар пользователя ukrlanser

Добрый день! Надеюсь, здесь я найду помощь
При загрузке кде появляется окно - Sound server informational message:
Error while initializing the sound driver:
device: default can't be opened for playback (Device or resource busy)
The sound server will continue, using the null output device.

Вывод dmesg-

Linux version 2.6.23.17-88.0.120asp (build@server3.asplinux.com.ua) (gcc version 4.1.2 20070925 (ASPLinux 4.1.2-27)) #1 SMP Mon May 19 17:49:15 EEST 2008
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000007ffc0000 (usable)
BIOS-e820: 000000007ffc0000 - 000000007ffce000 (ACPI data)
BIOS-e820: 000000007ffce000 - 000000007fff0000 (ACPI NVS)
BIOS-e820: 000000007fff0000 - 0000000080000000 (reserved)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
1151MB HIGHMEM available.
896MB LOWMEM available.
found SMP MP-table at 000ff780
Using x86 segment limits to approximate NX protection
Entering add_active_range(0, 0, 524224) 0 entries of 256 used
Zone PFN ranges:
DMA 0 -> 4096
Normal 4096 -> 229376
HighMem 229376 -> 524224
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0 -> 524224
On node 0 totalpages: 524224
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 4064 pages, LIFO batch:0
Normal zone: 1760 pages used for memmap
Normal zone: 223520 pages, LIFO batch:31
HighMem zone: 2303 pages used for memmap
HighMem zone: 292545 pages, LIFO batch:31
Movable zone: 0 pages used for memmap
DMI present.
Using APIC driver default
ACPI: RSDP 000F9140, 0014 (r0 ACPIAM)
ACPI: RSDT 7FFC0000, 0040 (r1 MSI_NB MEGABOOK 20070828 MSFT 97)
ACPI: FACP 7FFC0200, 0084 (r2 082807 FACP1611 20070828 MSFT 97)
ACPI: DSDT 7FFC05B0, 5D29 (r1 AMHR_ AMHR_B38 B38 INTL 20051117)
ACPI: FACS 7FFCE000, 0040
ACPI: APIC 7FFC0390, 005C (r1 082807 APIC1611 20070828 MSFT 97)
ACPI: MCFG 7FFC03F0, 003C (r1 082807 OEMMCFG 20070828 MSFT 97)
ACPI: SLIC 7FFC0430, 0176 (r1 MSI_NB MEGABOOK 20070828 MSFT 97)
ACPI: OEMB 7FFCE040, 0071 (r1 082807 OEMB1611 20070828 MSFT 97)
ACPI: HPET 7FFC62E0, 0038 (r1 082807 OEMHPET 20070828 MSFT 97)
ACPI: SSDT 7FFC6320, 022E (r1 A M I POWERNOW 1 AMD 1)
ATI board detected. Disabling timer routing over 8254.
ACPI: PM-Timer IO Port: 0x808
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 15:8 APIC version 16
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
Processor #1 15:8 APIC version 16
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 33, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
ACPI: HPET id: 0x8300 base: 0xfed00000
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 88000000 (gap: 80000000:7ff80000)
swsusp: Registered nosave memory region: 000000000009f000 - 00000000000a0000
swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000e4000
swsusp: Registered nosave memory region: 00000000000e4000 - 0000000000100000
Built 1 zonelists in Zone order. Total pages: 520129
Kernel command line: ro root=/dev/VolGroup00/LogVol00 rhgb quiet
mapped APIC to ffffb000 (fee00000)
mapped IOAPIC to ffffa000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
CPU 0 irqstacks, hard=c07a6000 soft=c0786000
PID hash table entries: 4096 (order: 12, 16384 bytes)
Detected 1808.173 MHz processor.
Console: colour VGA+ 80x25
console [tty0] enabled
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 2070380k/2096896k available (2178k kernel code, 25260k reserved, 1114k data, 280k init, 1179392k highmem)
virtual kernel memory layout:
fixmap : 0xffc53000 - 0xfffff000 (3760 kB)
pkmap : 0xff800000 - 0xffc00000 (4096 kB)
vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB)
lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
.init : 0xc073d000 - 0xc0783000 ( 280 kB)
.data : 0xc0620abd - 0xc0737544 (1114 kB)
.text : 0xc0400000 - 0xc0620abd (2178 kB)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
SLUB: Genslabs=22, HWalign=64, Order=0-1, MinObjects=4, CPUs=2, Nodes=1
hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0
hpet0: 4 32-bit timers, 14318180 Hz
Calibrating delay using timer specific routine.. 3712.41 BogoMIPS (lpj=1856205)
Security Framework v1.0.0 initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
selinux_register_security: Registering secondary module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 178bfbff ebd3fbff 00000000 00000000 00002001 00000000 0000011f 00000000
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU 0(2) -> Core 0
CPU: After all inits, caps: 178bf3ff ebd3fbff 00000000 00000410 00002001 00000000 0000011f 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
ACPI: Core revision 20070126
CPU0: AMD Athlon(tm) 64 X2 Dual-Core Processor TK-55 stepping 01
SMP alternatives: switching to SMP code
Booting processor 1/1 eip 3000
CPU 1 irqstacks, hard=c07a7000 soft=c0787000
Initializing CPU#1
Calibrating delay using timer specific routine.. 3616.42 BogoMIPS (lpj=1808214)
CPU: After generic identify, caps: 178bfbff ebd3fbff 00000000 00000000 00002001 00000000 0000011f 00000000
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU 1(2) -> Core 1
CPU: After all inits, caps: 178bf3ff ebd3fbff 00000000 00000410 00002001 00000000 0000011f 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: AMD Athlon(tm) 64 X2 Dual-Core Processor TK-55 stepping 01
Total of 2 processors activated (7328.83 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
Brought up 2 CPUs
sizeof(vma)=84 bytes
sizeof(page)=32 bytes
sizeof(inode)=336 bytes
sizeof(dentry)=132 bytes
sizeof(ext3inode)=488 bytes
sizeof(buffer_head)=56 bytes
sizeof(skbuff)=180 bytes
sizeof(task_struct)=1552 bytes
Booting paravirtualized kernel on bare hardware
Time: 16:51:36 Date: 11/14/09
NET: Registered protocol family 16
No dock devices found.
ACPI: bus type pci registered
PCI: PCI BIOS revision 3.00 entry at 0xf0031, last bus=6
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: EC: Look up EC in DSDT
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
Error attaching device data
Error attaching device data
ACPI: EC: GPE = 0x6, I/O: command/status = 0x66, data = 0x62
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Transparent bridge - 0000:00:14.4
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCE2._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCE5._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCE6._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0PC._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCE7._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 9) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 12 devices
ACPI: ACPI bus type pnp unregistered
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
NetLabel: Initializing
NetLabel: domain hash size = 128
NetLabel: protocols = UNLABELED CIPSOv4
NetLabel: unlabeled traffic allowed by default
Time: hpet clocksource has been installed.
Clockevents: could not switch to one-shot mode: lapic is not functional.
Could not switch to high resolution mode on CPU 0
Clockevents: could not switch to one-shot mode: lapic is not functional.
Could not switch to high resolution mode on CPU 1
pnp: 00:06: iomem range 0xfec00000-0xfec00fff has been reserved
pnp: 00:06: iomem range 0xfee00000-0xfee00fff has been reserved
pnp: 00:07: iomem range 0xffb80000-0xffbfffff has been reserved
pnp: 00:07: iomem range 0xfff80000-0xffffffff could not be reserved
pnp: 00:0a: iomem range 0xe0000000-0xefffffff has been reserved
pnp: 00:0b: iomem range 0x0-0x9ffff could not be reserved
pnp: 00:0b: iomem range 0xc0000-0xcffff could not be reserved
pnp: 00:0b: iomem range 0xe0000-0xfffff could not be reserved
pnp: 00:0b: iomem range 0x100000-0x7fffffff could not be reserved
PCI: Bridge: 0000:00:02.0
IO window: c000-cfff
MEM window: fde00000-fdefffff
PREFETCH window: f0000000-f7ffffff
PCI: Bridge: 0000:00:05.0
IO window: disabled.
MEM window: fdf00000-fdffffff
PREFETCH window: disabled.
PCI: Bridge: 0000:00:06.0
IO window: d000-dfff
MEM window: fe000000-fe9fffff
PREFETCH window: fa000000-fcffffff
PCI: Bridge: 0000:00:07.0
IO window: e000-efff
MEM window: fea00000-feafffff
PREFETCH window: disabled.
PCI: Bridge: 0000:00:14.4
IO window: disabled.
MEM window: feb00000-febfffff
PREFETCH window: disabled.
PCI: Setting latency timer of device 0000:00:02.0 to 64
PCI: Setting latency timer of device 0000:00:05.0 to 64
PCI: Setting latency timer of device 0000:00:06.0 to 64
PCI: Setting latency timer of device 0000:00:07.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1572864 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
checking if image is initramfs... it is
Freeing initrd memory: 3540k freed
apm: BIOS not found.
audit: initializing netlink socket (disabled)
audit(1258217496.559:1): initialized
highmem bounce pool size: 64 pages
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
SELinux: Registering netfilter hooks
ksign: Installing public key data
Loading keyring
- Added public key 5A559A85A0AFC4E8
- User ID: ASPLinux, Ltd. (Kernel Module GPG key)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
PCI: MSI quirk detected. MSI deactivated.
Boot video device is 0000:01:00.0
PCI: Setting latency timer of device 0000:00:02.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:02.0:pcie00]
PCI: Setting latency timer of device 0000:00:05.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:05.0:pcie00]
PCI: Setting latency timer of device 0000:00:06.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:06.0:pcie00]
Allocate Port Service[0000:00:06.0:pcie02]
PCI: Setting latency timer of device 0000:00:07.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:07.0:pcie00]
Allocate Port Service[0000:00:07.0:pcie02]
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
ACPI: duty_cycle spans bit 4
ACPI: Thermal Zone [THRM] (34 C)
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12ac
hpet_resources: 0xfed00000 is busy
Non-volatile memory driver v1.2
Linux agpgart interface v0.102
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
RAMDISK driver initialized: 16 RAM disks of 16384K size 4096 blocksize
input: Macintosh mouse button emulation as /class/input/input0
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
i8042.c: Detected active multiplexing controller, rev 1.1.
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard as /class/input/input1
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
powernow-k8: Found 1 AMD Athlon(tm) 64 X2 Dual-Core Processor TK-55 processors (2 cpu cores) (version 2.00.00)
powernow-k8: 0 : fid 0xa (1800 MHz), vid 0x13
powernow-k8: 1 : fid 0x8 (1600 MHz), vid 0x14
powernow-k8: 2 : fid 0x0 (800 MHz), vid 0x1a
Using IPI No-Shortcut mode
Magic number: 1:120:894
Freeing unused kernel memory: 280k freed
Write protecting the kernel read-only data: 847k
USB Universal Host Controller Interface driver v3.0
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
ACPI: PCI Interrupt 0000:00:13.0[A] -> GSI 16 (level, low) -> IRQ 16
ohci_hcd 0000:00:13.0: OHCI Host Controller
ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 1
ohci_hcd 0000:00:13.0: irq 16, io mem 0xfddfe000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:13.1[B] -> GSI 17 (level, low) -> IRQ 17
ohci_hcd 0000:00:13.1: OHCI Host Controller
ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:13.1: irq 17, io mem 0xfddfd000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:13.2[C] -> GSI 18 (level, low) -> IRQ 18
ohci_hcd 0000:00:13.2: OHCI Host Controller
ohci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 3
ohci_hcd 0000:00:13.2: irq 18, io mem 0xfddfc000
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
input: ImPS/2 Logitech Wheel Mouse as /class/input/input2
ACPI: PCI Interrupt 0000:00:13.3[B] -> GSI 17 (level, low) -> IRQ 17
ohci_hcd 0000:00:13.3: OHCI Host Controller
ohci_hcd 0000:00:13.3: new USB bus registered, assigned bus number 4
ohci_hcd 0000:00:13.3: irq 17, io mem 0xfddfb000
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:13.4[C] -> GSI 18 (level, low) -> IRQ 18
ohci_hcd 0000:00:13.4: OHCI Host Controller
ohci_hcd 0000:00:13.4: new USB bus registered, assigned bus number 5
ohci_hcd 0000:00:13.4: irq 18, io mem 0xfddfa000
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
usb 3-1: new low speed USB device using ohci_hcd and address 2
ACPI: PCI Interrupt 0000:00:13.5[D] -> GSI 19 (level, low) -> IRQ 19
ehci_hcd 0000:00:13.5: EHCI Host Controller
ehci_hcd 0000:00:13.5: new USB bus registered, assigned bus number 6
ehci_hcd 0000:00:13.5: debug port 1
ehci_hcd 0000:00:13.5: irq 19, io mem 0xfddff000
ehci_hcd 0000:00:13.5: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb6: configuration #1 chosen from 1 choice
hub 6-0:1.0: USB hub found
hub 6-0:1.0: 10 ports detected
SCSI subsystem initialized
libata version 2.21 loaded.
ahci 0000:00:12.0: version 2.3
ACPI: PCI Interrupt 0000:00:12.0[A] -> GSI 22 (level, low) -> IRQ 20
ahci 0000:00:12.0: controller can't do 64bit DMA, forcing 32bit
usb 3-1: device not accepting address 2, error -62
usb 3-1: new low speed USB device using ohci_hcd and address 4
ahci 0000:00:12.0: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl SATA mode
ahci 0000:00:12.0: flags: ncq sntf ilck pm led clo pmp pio slum part
scsi0 : ahci
scsi1 : ahci
scsi2 : ahci
scsi3 : ahci
ata1: SATA max UDMA/133 cmd 0xf884e900 ctl 0x00000000 bmdma 0x00000000 irq 20
ata2: SATA max UDMA/133 cmd 0xf884e980 ctl 0x00000000 bmdma 0x00000000 irq 20
ata3: SATA max UDMA/133 cmd 0xf884ea00 ctl 0x00000000 bmdma 0x00000000 irq 20
ata4: SATA max UDMA/133 cmd 0xf884ea80 ctl 0x00000000 bmdma 0x00000000 irq 20
usb 3-1: configuration #1 chosen from 1 choice
input: Microsoft Basic Optical Mouse as /class/input/input3
input: USB HID v1.10 Mouse [Microsoft Basic Optical Mouse] on usb-0000:00:13.2-1
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: ATA-7: WDC WD1600BEVS-22RST0, 04.01G04, max UDMA/133
ata1.00: 312581808 sectors, multi 16: LBA48 NCQ (depth 31/32)
ata1.00: configured for UDMA/133
ata2: SATA link down (SStatus 0 SControl 300)
ata3: SATA link down (SStatus 0 SControl 300)
ata4: SATA link down (SStatus 0 SControl 300)
scsi 0:0:0:0: Direct-Access ATA WDC WD1600BEVS-2 04.0 PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2 sda3
sd 0:0:0:0: [sda] Attached SCSI disk
ACPI: PCI Interrupt 0000:00:14.1[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:14.1 to 64
scsi4 : pata_atiixp
scsi5 : pata_atiixp
ata5: PATA max UDMA/100 cmd 0x000101f0 ctl 0x000103f6 bmdma 0x0001ff00 irq 14
ata6: PATA max UDMA/100 cmd 0x00010170 ctl 0x00010376 bmdma 0x0001ff08 irq 15
ata5.00: ATAPI: Optiarc DVD RW AD-7530B, NX02, max UDMA/33
ata5.00: configured for UDMA/33
scsi 4:0:0:0: CD-ROM Optiarc DVD RW AD-7530B NX02 PQ: 0 ANSI: 5
device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com
EXT3-fs: INFO: recovery required on readonly filesystem.
EXT3-fs: write access will be enabled during recovery.
kjournald starting. Commit interval 5 seconds
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: Disabled at runtime.
SELinux: Unregistering netfilter hooks
audit(1258217507.790:2): selinux=0 auid=4294967295
sd 0:0:0:0: Attached scsi generic sg0 type 0
scsi 4:0:0:0: Attached scsi generic sg1 type 5
sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 4:0:0:0: Attached scsi CD-ROM sr0
r8169 Gigabit Ethernet driver 2.2LK-NAPI loaded
ACPI: PCI Interrupt 0000:05:00.0[A] -> GSI 19 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:05:00.0 to 64
eth0: RTL8168b/8111b at 0xf8868000, 00:19:db:eb:78:fc, XID 38000000 IRQ 19
fglrx: module license 'Proprietary. (C) 2002 - ATI Technologies, Starnberg, GERMANY' taints kernel.
[fglrx] vendor: 1002 device: 94c9 count: 1
[fglrx] ioport: bar 1, base 0xc000, size: 0x100
[fglrx] Maximum main memory to use for locked dma buffers: 1898 MBytes.
[fglrx] PAT is enabled successfully!
[fglrx] module loaded - fglrx 8.51.3 [Jul 3 2008] with 1 minors
input: PC Speaker as /class/input/input4
input: Power Button (FF) as /class/input/input5
piix4_smbus 0000:00:14.0: Found 0000:00:14.0 device
ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 17 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:02:00.0 to 64
ath5k_pci 0000:02:00.0: registered as 'phy0'
ath5k phy0: failed to resume the MAC Chip
ACPI: PCI interrupt for device 0000:02:00.0 disabled
ACPI: Power Button (FF) [PWRF]
input: Lid Switch as /class/input/input6
ACPI: Lid Switch [LID0]
input: Sleep Button (CM) as /class/input/input7
ACPI: Sleep Button (CM) [SLPB]
input: Power Button (CM) as /class/input/input8
ACPI: Power Button (CM) [PWRB]
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
ACPI: Battery Slot [BAT1] (battery present)
ACPI: AC Adapter [ADP1] (on-line)
input: Video Bus as /class/input/input9
ACPI: Video Device [VGA] (multi-head: yes rom: no post: no)
ath5k_pci: probe of 0000:02:00.0 failed with error -5
sdhci: SDHCI controller found at 0000:06:04.1 [1180:0822] (rev 22)
ACPI: PCI Interrupt 0000:06:04.1[B] -> GSI 21 (level, low) -> IRQ 21
mmc0: SDHCI at 0xfebff400 irq 21 DMA
ACPI: PCI Interrupt 0000:06:04.0[A] -> GSI 20 (level, low) -> IRQ 22
firewire_ohci: Added fw-ohci device 0000:06:04.0, OHCI version 1.10
ACPI: PCI Interrupt 0000:00:14.2[A] -> GSI 16 (level, low) -> IRQ 16
hda_codec: Unknown model for ALC883, trying auto-probe from BIOS...
ACPI: PCI Interrupt 0000:01:00.1[B] -> GSI 19 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:01:00.1 to 64
firewire_core: created device fw0: GUID 00dc1000917e3401, S400
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 18 (level, low) -> IRQ 18
floppy0: no floppy controllers found
device-mapper: multipath: version 1.0.5 loaded
EXT3 FS on dm-0, internal journal
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda2, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Adding 2031608k swap on /dev/VolGroup00/LogVol01. Priority:-1 extents:1 across:2031608k
Clocksource tsc unstable (delta = -277701535 ns)
ip6_tables: (C) 2000-2006 Netfilter Core Team
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
ip_tables: (C) 2000-2006 Netfilter Core Team
r8169: eth0: link up
r8169: eth0: link up
r8169: eth0: link up
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky
Bluetooth: Core ver 2.11
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.8
Bluetooth: L2CAP socket layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM ver 1.8
Bluetooth: HIDP (Human Interface Emulation) ver 1.2
eth0: no IPv6 routers present
BUG: unable to handle kernel NULL pointer dereference at virtual address 00000018
printing eip:
f8a8fb55
*pde = 769d5067
Oops: 0002 [#1]
SMP
Modules linked in: autofs4 hidp rfcomm l2cap bluetooth tun sunrpc nf_conntrack_netbios_ns nf_conntrack_ipv4 ipt_REJECT iptable_filter ip_tables nf_conntrack_ipv6 xt_state nf_conntrack nfnetlink xt_tcpudp ip6t_REJECT ip6table_filter ip6_tables x_tables cpufreq_ondemand dm_multipath sbs ipv6 snd_seq_dummy snd_hda_intel snd_seq_oss snd_seq_midi_event snd_seq snd_seq_device snd_pcm_oss snd_mixer_oss snd_pcm firewire_ohci firewire_core video output ac battery crc_itu_t sdhci mmc_core ath5k k8temp serio_raw i2c_piix4 button pcspkr snd_timer hwmon i2c_core snd_page_alloc snd_hwdep mac80211 fglrx(P)(U) snd r8169 cfg80211 soundcore sr_mod cdrom sg dm_snapshot dm_zero dm_mirror dm_mod pata_atiixp ahci libata sd_mod scsi_mod ext3 jbd mbcache ehci_hcd ohci_hcd uhci_hcd
CPU: 1
EIP: 0060:[] Tainted: P VLI
EFLAGS: 00210246 (2.6.23.17-88.0.120asp #1)
EIP is at azx_pcm_prepare+0xc9/0x210 [snd_hda_intel]
eax: 00000000 ebx: 00000000 ecx: 00000000 edx: 00000000
esi: f75c9e38 edi: 37750000 ebp: f7c01d00 esp: f6b61d40
ds: 007b es: 007b fs: 00d8 gs: 0033 ss: 0068
Process nasd (pid: 2553, ti=f6b61000 task=f6962000 task.ti=f6b61000)
Stack: 00000010 00000000 f6b63504 000001b2 00000000 000000d2 f7f5b770 f7c01400
f76fc4a4 f7c01d00 00009001 f8a04094 f7c01d00 f89f7762 00000000 f89f74c9
f7c01d00 00009001 f8a04094 f7c01d00 f89f8294 f76b2200 f76b2200 00009001
Call Trace:
[] snd_pcm_do_prepare+0x9/0x19 [snd_pcm]
[] snd_pcm_action_single+0x1d/0x40 [snd_pcm]
[] snd_pcm_action_nonatomic+0x43/0x56 [snd_pcm]
[] snd_pcm_common_ioctl1+0x609/0xed9 [snd_pcm]
[] native_smp_call_function_mask+0xca/0x103
[] map_vm_area+0x117/0x158
[] __alloc_pages+0x64/0x2a2
[] acpi_button_remove_fs+0x0/0x52 [button]
[] __vmalloc_area_node+0xf1/0x10f
[] snd_pcm_oss_change_params+0xed1/0xf17 [snd_pcm_oss]
[] snd_pcm_playback_ioctl1+0x353/0x36d [snd_pcm]
[] snd_pcm_kernel_ioctl+0x3a/0x5d [snd_pcm]
[] snd_pcm_oss_prepare+0x13/0x41 [snd_pcm_oss]
[] snd_pcm_oss_make_ready+0x32/0x46 [snd_pcm_oss]
[] snd_pcm_oss_sync+0x31/0x356 [snd_pcm_oss]
[] snd_pcm_oss_release+0x2c/0x83 [snd_pcm_oss]
[] __fput+0xbb/0x171
[] filp_close+0x51/0x58
[] sys_close+0x6e/0xa5
[] syscall_call+0x7/0xb
=======================
Code: c7 04 24 53 4d aa f8 e8 b8 3e ec ff b8 ea ff ff ff e9 54 01 00 00 8b 46 24 31 db 31 d2 8b 0e 8b 40 70 8b b8 f4 01 00 00 8b 46 1c 40 18 00 00 00 00 8b 46 1c c7 40 1c 00 00 00 00 eb 26 89 d8
EIP: [] azx_pcm_prepare+0xc9/0x210 [snd_hda_intel] SS:ESP 0068:f6b61d40
BUG: unable to handle kernel NULL pointer dereference at virtual address 00000003
printing eip:
c048ffc7
*pde = 00000000
Oops: 0000 [#2]
SMP
Modules linked in: autofs4 hidp rfcomm l2cap bluetooth tun sunrpc nf_conntrack_netbios_ns nf_conntrack_ipv4 ipt_REJECT iptable_filter ip_tables nf_conntrack_ipv6 xt_state nf_conntrack nfnetlink xt_tcpudp ip6t_REJECT ip6table_filter ip6_tables x_tables cpufreq_ondemand dm_multipath sbs ipv6 snd_seq_dummy snd_hda_intel snd_seq_oss snd_seq_midi_event snd_seq snd_seq_device snd_pcm_oss snd_mixer_oss snd_pcm firewire_ohci firewire_core video output ac battery crc_itu_t sdhci mmc_core ath5k k8temp serio_raw i2c_piix4 button pcspkr snd_timer hwmon i2c_core snd_page_alloc snd_hwdep mac80211 fglrx(P)(U) snd r8169 cfg80211 soundcore sr_mod cdrom sg dm_snapshot dm_zero dm_mirror dm_mod pata_atiixp ahci libata sd_mod scsi_mod ext3 jbd mbcache ehci_hcd ohci_hcd uhci_hcd
CPU: 1
EIP: 0060:[] Tainted: P D VLI
EFLAGS: 00210206 (2.6.23.17-88.0.120asp #1)
EIP is at dput+0xb/0xd7
eax: 00000003 ebx: 00000003 ecx: f7596318 edx: 01898000
esi: f7e06610 edi: 00000001 ebp: f7036000 esp: f7036f70
ds: 007b es: 007b fs: 00d8 gs: 0000 ss: 0068
Process gnome-pty-helpe (pid: 1456, ti=f7036000 task=f7e06610 task.ti=f7036000)
Stack: f75c9e40 c043024f 00000004 c0481732 f7036fa0 f7596300 f77eccc0 fffffff7
00000000 00000000 f7582380 00000000 f7036000 c0430731 00000000 00518260
00518260 c040518a 00000000 00000007 00000000 00518260 00518260 bf8b5648
Call Trace:
[] do_exit+0x290/0x6fc
[] vfs_read+0xba/0x158
[] sys_exit_group+0x0/0xd
[] syscall_call+0x7/0xb
=======================
Code: c2 01 f2 6b f2 0b 49 43 83 f9 ff 75 e6 89 f8 89 e2 89 34 24 e8 14 fe ff ff 83 c4 0c 5b 5e 5f c3 53 85 c0 89 c3 0f 84 ca 00 00 00 <83> 38 01 75 14 ba b5 00 00 00 b8 a3 71 6b c0 e8 f2 5d f9 ff e8
EIP: [] dput+0xb/0xd7 SS:ESP 0068:f7036f70
Fixing recursive fault but reboot is needed!
[fglrx] Reserved FB block: Shared offset:0, size:1000000
[fglrx] Reserved FB block: Unshared offset:7f7b000, size:80000
[fglrx] Reserved FB block: Unshared offset:7ffc000, size:4000
PPP generic driver version 2.4.2

Однако, при воспроизведении музыки или фильмов звук есть!
Что мне делать? Надеюсь на Вашу помощь!

Аватар пользователя Писатель

Re: Отсутствует звук, но ... музыка ...

Очевидно, что проблема в драйвере... У меня тоже самое было с моим adsl модемом. Долго мучился, и решил проблему именно последовательным перебором всевозможных драйверов.

RSS-материал