Как заставить работать гигабитный адаптер?

Автор: Doctor Death Дата: 05.04.2006 10:40 есть мать ASUS со встроенной гигабитной картой Marvell Yukon/SysKonnect SK-98xx Gigabit Ethernet Adapter
вроде в ASP 9.2 присутсвует драйвер от этой карты (покране мере в lib/modules/device/net - есть папка с sk98lin.o
но при попытки изировать модуль
выдаёт вот что:
][root@DarkToverIII net]# modprobe sk98lin
/lib/modules/2.4.22-1.2154.nptl.aspsmp/kernel/drivers/net/sk98lin/sk98lin.o: init_module: No such device
Hint: insmod errors can be caused by incorrect module parameters, including invalid IO or IRQ parameters.
You may find more information in syslog or the output from dmesg
/lib/modules/2.4.22-1.2154.nptl.aspsmp/kernel/drivers/net/sk98lin/sk98lin.o: insmod /lib/modules/2.4.22-1.2154.nptl.aspsmp/kernel/drivers/net/sk98lin/sk98lin.o failed
/lib/modules/2.4.22-1.2154.nptl.aspsmp/kernel/drivers/net/sk98lin/sk98lin.o: insmod sk98lin failed
[root@DarkToverIII net]#


как заставить работать эту карту?
Re: как заставить работать гигабитный адаптер? 05.04.2006 11:38INF[SZ] переведите Hint
Re: как заставить работать гигабитный адаптер? 05.04.2006 12:16Doctor Death перевести что?
то что ответил линукс на комманду иницилизации модуля дравера? или перевести что?
Re: как заставить работать гигабитный адаптер? 05.04.2006 12:38INF[SZ] Что выдает dmesg|more на тему сетевого адаптера
Re: как заставить работать гигабитный адаптер? 05.04.2006 14:59Doctor Death интересно а что он должен выдовать если адаптер не заиницилизированн???
Re: как заставить работать гигабитный адаптер? 05.04.2006 22:13ShaMAN Скорее всего версия драйвера sk98lin старая и не понимает эту карточку
---
[shaman@xxx ~]$ lspci -v -s 02:00.0
02:00.0 Ethernet controller: Marvell Technology Group Ltd. Gigabit Ethernet Controller (rev 19)
Subsystem: Giga-byte Technology Marvell 88E8053 Gigabit Ethernet Controller (Gigabyte)
Flags: bus master, fast devsel, latency 0, IRQ 193
Memory at e1000000 (64-bit, non-prefetchable)
I/O ports at a000
Capabilities: <available only to root>

[shaman@xxx ~]$ strings /lib/modules/`uname -r`/kernel/drivers/net/sk98lin/sk98lin.ko | grep 'Network Device Driver'
sk98lin: Network Device Driver v8.23.1.3
[shaman@xxx ~]$
---
Надо обновить модуль на более свежий
[www.skd.de]
Re: как заставить работать гигабитный адаптер? 06.04.2006 04:27INF[SZ] Либо взять RPM. Например тут
[atrpms.net]
Re: как заставить работать гигабитный адаптер? 06.04.2006 07:29Doctor Death [root@DarkToverIII root]# dmesg|more
Linux version 2.4.22-1.2154.nptl.aspsmp (build@ws163.outpost.sw.ru) (gcc version
3.3.2 20031022 (ASPLinux 3.3.2-1)) #1 SMP Wed Jan 14 19:48:31 MSK 2004
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000007fea0000 (usable)
BIOS-e820: 000000007fea0000 - 000000007feae000 (ACPI data)
BIOS-e820: 000000007feae000 - 000000007fee0000 (ACPI NVS)
BIOS-e820: 000000007fee0000 - 000000007ff00000 (reserved)
BIOS-e820: 00000000ffb80000 - 0000000100000000 (reserved)
1150MB HIGHMEM available.
896MB LOWMEM available.
ACPI: have wakeup address 0xc0002000
found SMP MP-table at 000ff780
hm, page 000ff000 reserved twice.
hm, page 00100000 reserved twice.
hm, page 000f0000 reserved twice.
hm, page 000f1000 reserved twice.
On node 0 totalpages: 523936
zone(0): 4096 pages.
zone(1): 225280 pages.
zone(2): 294560 pages.
ACPI: RSDP (v000 ACPIAM ) @ 0x000fa520
ACPI: RSDT (v001 A M I OEMRSDT 0x10000527 MSFT 0x00000097) @ 0x7fea0000
ACPI: FADT (v001 A M I OEMFACP 0x10000527 MSFT 0x00000097) @ 0x7fea0200
ACPI: MADT (v001 A M I OEMAPIC 0x10000527 MSFT 0x00000097) @ 0x7fea0390
ACPI: OEMB (v001 A M I AMI_OEM 0x10000527 MSFT 0x00000097) @ 0x7feae040
>>> ERROR: Invalid checksum
ACPI: MCFG (v001 A M I OEMMCFG 0x10000527 MSFT 0x00000097) @ 0x7fea4eb0
ACPI: ASF! (v032 LEGEND I865PASF 0x00000001 INTL 0x02002026) @ 0x7fea4eec
ACPI: DSDT (v001 A0281 A0281040 0x00000040 INTL 0x02002026) @ 0x00000000
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 Unknown CPU [15:6] APIC version 20
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
Processor #1 Unknown CPU [15:6] APIC version 20
Using ACPI for processor (LAPIC) configuration information
Intel MultiProcessor Specification v1.1
Virtual Wire compatibility mode.
OEM ID: INTEL Product ID: APIC at: 0xFEE00000
I/O APIC #2 Version 32 at 0xFEC00000.
Processors: 2
xAPIC support is present
Enabling APIC mode: Flat. Using 1 I/O APICs
Kernel command line: root=/dev/hda2 rhgb
Initializing CPU#0
Detected 3200.530 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 6383.20 BogoMIPS
Memory: 2066268k/2095744k available (1602k kernel code, 29088k reserved, 1194k d
ata, 164k init, 1178240k highmem)
Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
Inode cache hash table entries: 131072 (order: 8, 1048576 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 131072 (order: 7, 524288 bytes)
Page-cache hash table entries: 524288 (order: 9, 2097152 bytes)
CPU: Trace cache: 12K uops<6>CPU: Physical Processor ID: 0
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: bfebfbff 20000000 00000000 00000000
CPU: Common caps: bfebfbff 20000000 00000000 00000000
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
mtrr: detected mtrr type: Intel
CPU: Trace cache: 12K uops<6>CPU: Physical Processor ID: 0
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: bfebfbff 20000000 00000000 00000000
CPU: Common caps: bfebfbff 20000000 00000000 00000000
CPU0: Intel(R) Pentium(R) D CPU 3.20GHz stepping 02
per-CPU timeslice cutoff: 0.00 usecs.
task migration cache decay timeout: 10 msecs.
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Booting processor 1/1 eip 3000
Initializing CPU#1
masked ExtINT on CPU#1
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Calibrating delay loop... 6396.31 BogoMIPS
CPU: Trace cache: 12K uops<6>CPU: Physical Processor ID: 0
Intel machine check reporting enabled on CPU#1.
CPU: After generic, caps: bfebfbff 20000000 00000000 00000000
CPU: Common caps: bfebfbff 20000000 00000000 00000000
CPU1: Intel(R) Pentium(R) D CPU 3.20GHz stepping 02
Total of 2 processors activated (12779.52 BogoMIPS).
ENABLING IO-APIC IRQs
Setting 2 in the phys_id_present_map
...changing IO-APIC physical APIC ID to 2 ... ok.
init IO_APIC IRQs
IO-APIC (apicid-pin) 2-0, 2-3, 2-5, 2-10, 2-11, 2-21, 2-23 not connected.
..TIMER: vector=0x31 pin1=2 pin2=0
number of MP IRQ sources: 25.
number of IO-APIC #2 registers: 24.
testing the IO APIC.......................

IO APIC #2......
.... register #00: 02000000
....... : physical APIC id: 02
....... : Delivery Type: 0
....... : LTS : 0
.... register #01: 00170020
....... : max redirection entries: 0017
....... : PRQ implemented: 0
....... : IO APIC version: 0020
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 000 00 1 0 0 0 0 0 0 00
01 003 03 0 0 0 0 0 1 1 39
02 003 03 0 0 0 0 0 1 1 31
03 000 00 1 0 0 0 0 0 0 00
04 003 03 0 0 0 0 0 1 1 41
05 000 00 1 0 0 0 0 0 0 00
06 003 03 0 0 0 0 0 1 1 49
07 003 03 0 0 0 0 0 1 1 51
08 003 03 0 0 0 0 0 1 1 59
09 003 03 0 0 0 0 0 1 1 61
0a 000 00 1 0 0 0 0 0 0 00
0b 000 00 1 0 0 0 0 0 0 00
0c 003 03 0 0 0 0 0 1 1 69
0d 003 03 0 0 0 0 0 1 1 71
0e 003 03 0 0 0 0 0 1 1 79
0f 003 03 0 0 0 0 0 1 1 81
10 003 03 1 1 0 1 0 1 1 89
11 003 03 1 1 0 1 0 1 1 91
12 003 03 1 1 0 1 0 1 1 99
13 003 03 1 1 0 1 0 1 1 A1
14 003 03 1 1 0 1 0 1 1 A9
15 000 00 1 0 0 0 0 0 0 00
16 003 03 1 1 0 1 0 1 1 B1
17 000 00 1 0 0 0 0 0 0 00
IRQ to pin mappings:
IRQ0 -> 0:2
IRQ1 -> 0:1
IRQ4 -> 0:4
IRQ6 -> 0:6
IRQ7 -> 0:7
IRQ8 -> 0:8
IRQ9 -> 0:9
IRQ12 -> 0:12
IRQ13 -> 0:13
IRQ14 -> 0:14
IRQ15 -> 0:15
IRQ16 -> 0:16
IRQ17 -> 0:17
IRQ18 -> 0:18
IRQ19 -> 0:19
IRQ20 -> 0:20
IRQ22 -> 0:22
.................................... done.
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 3200.3756 MHz.
..... host bus clock speed is 200.0232 MHz.
cpu: 0, clocks: 2000232, slice: 666744
CPU0<T0:2000224,T1:1333472,D:8,S:666744,C:2000232>
cpu: 1, clocks: 2000232, slice: 666744
CPU1<T0:2000224,T1:666736,D:0,S:666744,C:2000232>
cpu_sibling_map[0] = 1
cpu_sibling_map[1] = 0
mapping CPU#0's runqueue to CPU#1's runqueue.
Starting migration thread for cpu 0
smp_num_cpus: 2.
Starting migration thread for cpu 1
ACPI: Subsystem revision 20031002
ACPI: Interpreter disabled.
PCI: PCI BIOS revision 2.10 entry at 0xf0031, last bus=3
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
PCI: Ignoring BAR0-3 of IDE controller 00:1f.1
Transparent bridge - Intel Corp. 82801BA/CA/DB/EB PCI Bridge
PCI: Discovered primary peer bus ff [IRQ]
PCI: Using IRQ router default [8086/27b8] at 00:1f.0
PCI->APIC IRQ transform: (B0,I2,P0) -> 16
PCI->APIC IRQ transform: (B0,I27,P0) -> 19
PCI->APIC IRQ transform: (B0,I28,P0) -> 16
PCI->APIC IRQ transform: (B0,I28,P1) -> 17
PCI->APIC IRQ transform: (B0,I29,P0) -> 20
PCI->APIC IRQ transform: (B0,I29,P1) -> 17
PCI->APIC IRQ transform: (B0,I29,P2) -> 18
PCI->APIC IRQ transform: (B0,I29,P3) -> 19
PCI->APIC IRQ transform: (B0,I29,P0) -> 20
PCI->APIC IRQ transform: (B0,I31,P0) -> 18
PCI->APIC IRQ transform: (B0,I31,P1) -> 17
PCI->APIC IRQ transform: (B0,I31,P1) -> 17
PCI->APIC IRQ transform: (B2,I0,P0) -> 17
PCI->APIC IRQ transform: (B1,I4,P0) -> 19
PCI->APIC IRQ transform: (B1,I10,P0) -> 22
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16)
apm: disabled - APM is not SMP safe.
Starting kswapd
allocated 32 pages and 32 bhs reserved for the highmem bounces
VFS: Disk quotas vdquot_6.5.1
Detected PS/2 Mouse Port.
pty: 2048 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS MULTIPORT SHARE_IRQ SER
IAL_PCI ISAPNP enabled
ttyS0 at 0x03f8 (irq = 4) is a 16550A
Real Time Clock Driver v1.10e
NET4: Frame Diverter 0.46
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
hda: ST3200822A, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: attached ide-disk driver.
hda: host protected area => 1
hda: 390721968 sectors (200050 MB-) w/8192KiB Cache, CHS=24321/255/63
Partition check:
hda: hda1 hda2 hda4 < hda5 hda6 >
ide: late registration of driver.
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
Initializing Cryptographic API
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 16384 buckets, 128Kbytes
TCP: Hash tables configured (established 262144 bind 65536)
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 489k freed
EXT2-fs warning: checktime reached, running e2fsck is recommended
VFS: Mounted root (ext2 filesystem).
Journalled Block Device driver loaded
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Freeing unused kernel memory: 164k freed
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,2), internal journal
Adding Swap: 2658716k swap-space (priority -1)
kjournald starting. Commit interval 5 seconds
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,5), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,6), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
ip_tables: (C) 2000-2002 Netfilter core team
3c59x: Donald Becker and others. www.scyld.com/network/vortex.html
See Documentation/networking/vortex.txt
01:0a.0: 3Com PCI 3c905C Tornado at 0xc800. Vers LK1.1.18-ac
00:04:76:a3:dc:68, IRQ 22
product code 4d58 rev 00.13 date 10-18-01
Internal config register is 1800000, transceivers 0xa.
8K byte-wide RAM 5:3 Rx:Tx split, autoselect/Autonegotiate interface.
MII transceiver found at address 24, status 782d.
Enabling bus-master transmits and whole-frame receives.
01:0a.0: scatter/gather enabled. h/w checksums enabled
divert: allocating divert_blk for eth0
ip_tables: (C) 2000-2002 Netfilter core team
sk98lin: No adapter found.
sk98lin: No adapter found.
sk98lin: No adapter found.
sk98lin: No adapter found.
sk98lin: No adapter found.
sk98lin: No adapter found.
sk98lin: No adapter found.
sk98lin: No adapter found.
sk98lin: No adapter found.
sk98lin: No adapter found.
sk98lin: No adapter found.
sk98lin: No adapter found.
sk98lin: No adapter found.
sk98lin: No adapter found.
sk98lin: No adapter found.
sk98lin: No adapter found.
sk98lin: No adapter found.
eth0: Too much work in interrupt, status e401.
eth0: Too much work in interrupt, status e401.
Re: как заставить работать гигабитный адаптер? 07.04.2006 09:06Doctor Death спасибо - рпм драйверы сработали
RSS-материал